Carbon Fiber Stem Mount

$100.00

Shipping calculated at checkout.

Carbon Fiber Stem Mount

The stem mount is intended to be used for Road and Gravel riding but not Freeride, All Mountain or other riding. It's made from 3K Twill carbon fiber plate, 7075-T6 aluminum and uses Titanium hardware. Made to mount to any stem with a bolt hole width of 21 to 36 mm.

Choose from either a Garmin or Wahoo adapter

The mount includes a Titanium bolt and nut with a nylon washer to mount a light or action camera like a GoPro.

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series, and WAHOO® Elemnt Roam and Element Bolt series computers.

Combo kit works with all GoPro® Hero Cameras, Action Cameras and Cycling lights.

Instructions:

Don’t apply excessive force when tightening, excessive force may break the product and void the warranty.

Stay under 5Nm of torque (or read the max tighten torque suggested on your stem). Lube the bolt with anti-seize grease

Before tightening make sure the titanium bolt penetrates into the stem threaded part at least 6 - 7mm.

Weights:

Mount + Computer adapter and hardware=33.4 grams

Mount + Camera/Light hardware=37.0 grams

Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Garmin Computer & Camera Mount

AS-GGP100B

$40.00

Shipping calculated at checkout.

Mount your Cycling Computer and Camera Out front and Center using just One mounting arm. Slide and Rotate the Computer to the Optimum Viewing Angle and position your camera below the bars and out of harms way.

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers and all GoPro® Hero Cameras and Action Cameras

Mounting Arm

Mount up to Two devices on one Mounting Arm
Mount your devices out-front or behind the bars
Rotate and slide your devices to multiple positions
Free up bar space with only one mount for all your devices
Buy only one mount and save money
No need to buy new mounts for new devices
Strong, light, and shock absorbing
Fits all 31.8mm diameter bars
Torque not to exceed 1.6Nm/14inlbs

Cycling Computer Adapter

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
Slide and Rotate: Slide and Rotate your computer to most positions.
Eliminate Glare: Rotate your computer to Eliminate Glare.
Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
Torque not to exceed 1.6Nm/14inlbs

Cycling Camera Adapter

Camera Adapter works with all GoPro® Hero Cameras and Action Cameras
Positions your Camera Out front and Center
Camera can be mounted facing forward or backwards
Rotate and Slide your Camera to capture different views
Mounts Upside down or Right side up
Easily remove and attach the camera with the quick release adapter
Torque not to exceed 1.6Nm/14inlbs.

Made from a CARBON composite Nylon
Weight 54g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Garmin Computer & Camera/Light Mount

AS-GCL100B

$40.00

Shipping calculated at checkout.

Mount your Cycling Computer and Camera or Light Out front and Center using just One mounting arm. Mount features a GoPro style 3 Tab adapter with M5 threaded insert. Slide and Rotate the Computer to the Optimum Viewing Angle and position your camera or light below the bars and out of harms way.

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers, all GoPro® Hero Cameras, Action Cameras and Cycling lights.

Mounting Arm

Mount up to Two devices on one Mounting Arm
Mount your devices out-front or behind the bars
Rotate and slide your devices to multiple positions
Free up bar space with only one mount for all your devices
Buy only one mount and save money
No need to buy new mounts for new devices
Strong, light, and shock absorbing
Fits all 31.8mm diameter bars
Torque not to exceed 1.6Nm/14inlbs

Cycling Computer Adapter

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
Slide and Rotate: Slide and Rotate your computer to most positions.
Eliminate Glare: Rotate your computer to Eliminate Glare.
Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
Torque not to exceed 1.6Nm/14inlbs

Cycling Camera & Light Adapter

Camera & Light Adapter works with all GoPro® Hero Cameras and Action Cameras and Cycling Lights with a Two Tab interface and M5 Bolt.
Lights require an Two Tab adapter to connect to our adapter like the K-Edge aluminum adapter.
Positions your Camera or Light Out front and Center
Camera can be mounted facing forward or backwards
Rotate and Slide your Camera to capture different views
Mounts Upside down or Right side up
Torque not to exceed 1.6Nm/14inlbs.

Made from a CARBON composite Nylon
Weight 54g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Garmin Computer & Light Mount

AS-GU101B

$40.00

Shipping calculated at checkout.

Mount your Cycling Computer and Light Out front and Center using just One mounting arm. Slide and Rotate the Computer to the Optimum Viewing Angle and position your Light lower to the ground for improved lighting.

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers and all Cycling lights that mount to a 31.8mm bar.

Mounting Arm

Mount up to Two devices on one Mounting Arm
Mount your devices out-front or behind the bars
Rotate and slide your devices to multiple positions
Free up bar space with only one mount for all your devices
Buy only one mount and save money
No need to buy new mounts for new devices
Strong, light, and shock absorbing
Fits all 31.8mm diameter bars
Torque not to exceed 1.6Nm/14inlbs

Cycling Computer Adapter

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
Slide and Rotate: Slide and Rotate your computer to most positions.
Eliminate Glare: Rotate your computer to Eliminate Glare.
Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
Torque not to exceed 1.6Nm/14inlbs

Universal Adapter

Mount any 31.8mm bar mountable device on the Universal Adapter
Mount a Light Out front, Center and lower to the ground for improved lighting
Mount your Cycling Computer Out front
Torque not to exceed 1.6Nm/14inlbs

Made from a CARBON composite Nylon
Weight 52g
Designed, engineered and manufactured in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Garmin Computer Adapter

AD-G100B

$10.00

Shipping calculated at checkout.

Mount your computer Out front and Center of the bars. Slide and Rotate to eliminate glare and optimize the viewing angle

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.

Features

Cycling Computer Adapter works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
Slide and Rotate: Slide and Rotate your computer to most positions.
Eliminate Glare: Rotate your computer to Eliminate Glare.
Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
Torque not to exceed 1.6Nm/14inlbs

Made from a CARBON composite Nylon
Weight 8g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Garmin Computer Mount

AS-G100B

$30.00

Shipping calculated at checkout.

Mount your Cycling Computer Out front and Center. Slide and Rotate to eliminate glare and optimize the viewing angle.

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers

Mounting Arm

Mount up to Two devices on one Mounting Arm
Mount your devices out-front or behind the bars
Rotate and slide your devices to multiple positions
Free up bar space with only one mount for all your devices
Buy only one mount and save money
No need to buy new mounts for new devices
Strong, light, and shock absorbing
Fits all 31.8mm diameter bars
Torque not to exceed 1.6Nm/14inlbs
Made from a CARBON composite Nylon

Cycling Computer Adapter

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
Slide and Rotate: Slide and Rotate your computer to most positions.
Eliminate Glare: Rotate your computer to Eliminate Glare.
Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
Torque not to exceed 1.6Nm/14inlbs

Made from a CARBON composite Nylon
Weight 37g
Designed, engineered, and manufactured in the U.S.A

Instructions

Mounting Arm

Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.

Adapters

Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

Currency

Carbon Fiber Stem Mount